Jim Michalak's Boat Designs
118 E Randall, Lebanon, IL 62254
A page of boat designs and essays.
(1sep07) This issue will rerun the taped seam essay. The 15 September issue will take a look at "relaminating" my Toto.
THE BOOK IS OUT!
BOATBUILDING FOR BEGINNERS (AND BEYOND)is out now, written by me and edited by Garth Battista of Breakaway Books. You might find it at your bookstore. If not check it out at the....
ON LINE CATALOG OF MY PLANS...
...which can now be found at Duckworks Magazine. You order with a shopping cart set up and pay with credit cards or by Paypal. Then Duckworks sends me an email about the order and then I send the plans right from me to you.
Wojtech Baginski is adding a sailrig to his Polish Polepunt.
I remember seeing taped seam construction first in an article in the old Small Boat Journal about Sam Devlin's efforts. That was probably about 15 years ago (time flies). But by then the method was old in England. I think it was "invented" by an Englishman in the late '50's and was quite common there by the 70's. The Mirror dinghy was done that way with kits meticulously made from plywood with notches and tabs to fit the pieces together like a balsa model airplane kit. I visited England in 1982 and saw hundreds of Mirrors stacked on end at Portsmouth. Around the same time kit makers like Clarkcraft were selling kits of kayaks made that way but they called the method "sewn seam" which I think threw some of us off. "Sewing plywood together with wire - that sounds hard!" I said to myself. Harold Payson and Phil Bolger tried it in the early 80's with several designs that are still around. Harold called it "tack and tape" because at the time he didn't like using wires to temporarily fasten the panels together. He used small nails and adhesive tape, then hot melt glue, but eventually came around to using wire like everyone else.
My own taped seam history started about 1985. I made a Payson/Bolger dory with taped seams even though it was originally designed to be made on a ladder frame with chine logs in the old fashioned way. Payson's book "Build Your Own Boat" had the complete dory plans and also included the side panel expansions! It was easy to build a taped seam version with no ladder frame. Harold used polyester resin in his projects probably for the same reason others have used it - it's cheap and available. So I used it too on that dory. I tried ordinary automotive Bondo to fillet the seams instead of the resin/filler mixes that Payson advised. That boat had but one layer of glass inside and out. I used it for about five years until it got crushed by another boat in a tornado. The transom tapes were ripped (but the polyester resin held), and the boat was sort of opened wide. I gave it to Jim Huxford who repaired it and rowed itfor a few more years. It might still be around somewhere. In many ways my boat Sportdory is a rework of that old dory.
Next for me came the Payson canoe, multichine taped seam boat. Also built of cheap plywood with polyester resin and automotive Bondo in the late 80's. It eventually went to Bob Archibald who may still have it.
Next for me was Piccup Pram in 1989. Cheap plywood and polyester resin and Bondo again. I still have it and use it. It's seen a lot of use.
Next was Roar (which evolved into Roar2) about 1990. Cheap plywood and polyester resin and Bondo. Still have it and it has seen a lot of use.
Next I think was Toto which sort of evolved from the Payson canoe. Cheap lauan plywood with epoxy resin this time but still with Bondo fillets. Still have it and it's seen a lot of use.
The last was WeeVee which used cheap lauan plywood and reverted back to polyester resin and Bondo. Still have it but it hasn't gotten the use of the other boats.
"What's with all the polyester resin and Bondo?" you ask. Anyone who mentions using these in the rec boatbuilding newsgroup gets pounded and made fun of. Even 15 years ago Payson was attacked for building with polyester. I didn't know any better and have really had no troubles. Whenever I use one of my polyester boats I tell it, "You'd better start falling apart soon. You're making those experts look bad and they are going to pound me on the newsgroup and make fun of me." So far my boats haven't listened.
Polyester has certainly worked OK for me. My boats are stored under cover as a rule (although some have been outdoors for months at a time). That may be a factor in their longevity with polyester. Where I live you can never expect to get your money back on a homemade boat, even the cost of materials. I think when we started 15 years ago we got polyester for $13 a gallon (good stuff too) while epoxy went for about $70 a gallon. Now we know where to get much cheaper epoxy. So now I advise epoxy and it really is better. Of course if you are using expensive plywood, etc., you need to use epoxy.
But now to the main story - how I tape seams.
SECURING THE JOINT WITH WIRES....
(This is how I do it. Others have their pet methods.) Not much too it. My boats are all designed from the inside out, so to speak. The dimensions are arranged such that the panels should make kissing contact on the inside edges as shown above. Usually the project is upside down at this time, sides, bulkheads stem and stern fastened together, and you are trying to put the bilge or bottom panels on with taped seams. You put the panels into position and drill pairs of holes about every 12" around the perimeter, about 1/4" in from the edges. You take pieces of soft wire, I prefer stainless steel aircraft "lock wire" but almost any wire will work if it is pliable, and cut lenths about 6" long and form them into a long U shape like a staple. Get inside the project and push the wire staples up through the holes so that the ends now stick out through the outside. Get outside with a pair of pliars and twist the wires until they tighten the panels together. If you overtighten you might break the wire or tear the wire right out of the wood. Eyeball the joints to make sure they are fair. You can open a joint up to maybe a half inch if it will help. If two panels are binding too tightly, you can run a saw down the joint to loosen it up. I think a small gap or V is preferred because it allows resin to flow in and seal the ends of the plywood. But the joint fit is really not too critical.
When all the panels are wired in I like to go over the outer joint with duct tape to further secure things and to provide a dam for future flowing fillets. Then flip the project upright. Here is what the prototype Larsboat looked like at this stage. You can see the duct tape and can make out the wires.
There are variations allowed of course. The spacing of the wire twists can be anything needed to secure the panel into position. You may need more wires in places. Some folks don't use wire. John Bell used nylon wire ties on his Sportdory as you see here:
Not all panels are edge to edge, of course. Bulkheads are sort of T joints and are a bit trickier to fit. They would join like this:
THE INNER SEAMS...
Flip the boat upright. Prepare to fillet and tape the inner seams by pushing the wires on the interior hard against the plywood with a screwdriver to make them easier to cover. (One disadvantage of using nylon wire ties might be that they won't stay hard against the plywood.)
Then precut the fiberglass tape to length and lay the pieces out in a logical way so you can grab them quickly when needed. I always use 3" wide glass tape. It has no adhesive but is only called tape because of its form. It's edges are treated to prevent unravelling. When loaded with set resin the edges will be bulkier than the center of the tape, leaving a ridge. Some folks don't like the ridge. Some folks cut glass cloth into strips to avoid the ridge. I've tried that too to it unraveled and I ended up with a lot of glass hair flying around. I prefer the ridge which is easily ground down after the resin sets.
THE REAL TRICK TO GETTING A GOOD TAPED SEAM...
...is to do a seam all at once if possible. That would mean putting down the fillet and then the tape straight into it before the fillet sets. If more than one layer of glass is involved you put the extra layers right onto the first ones before they set. This way you avoid all the nasty sanding you face if you let a layer cure first. (Any cured resin system must be sanded before applying another layer, or paint.) It saves a tremendous amount of work. And you can be sure the whole thing is bonded together. So when you start you must have all you stuff together and ready to go.
In epoxy here is how I would do the job. Mix up some unthickened slow setting epoxy and brush it on the joint with a disposable bristle brush to "prime" the joint. (Some say the prime is a waste since epoxy doesn't really penetrate wood as some ads imply.) Mix up another batch with filler to make filleting mixture about as thick as Bondo. I think most any common filler is OK since you won't be sanding it. See Dave Carnell's page down in the links to get his view on epoxy and fillers. Lay down a fillet of the thickened epoxy over the joint and right over the wires. For a filleting tool I would recommend a tongue depressor 1" wide. I've heard a 3D tool like a tennis ball on the end of a stick is even better. In my view the fillet has to be there for strength but it should not be too large, say no more than 1" wide. It need not be perfectly smooth now but you will have to scoop up stray globs with a putty knife. The fillet should look like this:
Next brush some more thin epoxy over the joint and put the tape straight on top. Brush in more resin to saturate. The tape and the brushing will help to smooth out the fillet. Doing it this way you will most likely need to do short stretches at a time, maybe three feet. No problem with slow epoxy. Just do a stretch and pick up again at the unfinished end. When this all cures you will have a good interior joint with no sanding!
Here are two possible problem areas: One is where a temporary form blocks the tape job. Let it go for now and just end the tape an inch or so each side of the form. Finish later when the outside is done and the forms can be removed. Second is at corners such as where side bilge and bulkhead all meet. Fillet the corner with putty. Cut the tapes such that they will all overlap about an inch at the corner. Paste them down one by one into the corner. You will find that the tape is flexible enough to conform to the corner shape and yet the overlap is plenty to provide continuity.
Here is how I would do the job in polyester. The Bondo will usually set faster than you can slap down the tapes with polyester resin. I'll bet an expert would know how to catalyze the Bondo and resin such that you could get the thing to cure all at once as with the epoxy. You might experiment. Unlike epoxy, with polyester you can vary the catalyst to get different curing times. If you don't feel comfortable doing that, do this: Make the fillets in Bondo and let it cure hard. Sand it smooth with rough sandpaper, either a strip rolled into a tube or taped to the edge of a board rounded to the proper radius. Another handy way to sand the interior fillets is with a 2" rubber disk in an electric drill with very coarse paper. Then paste the tapes down with polyester resin as with epoxy. (On Toto I pasted the tapes down with epoxy resin over the Bondo joint.)
TAPING THE OUTER SEAMS....
These are simple compared to the inner seams.
Snip off the wires as close to the wood as possible. Some builders pull the wires out, sometimes first heating them, but I never had consistant luck with pulling wires. Stainless or copper wires left inside won't rust. Plain steel wire will rust although that is really a only cosmetic problem.
Fair the outer seams with putty as required. Most likely you will have to let the putty cure hard and sand to shape, unlike the inner seams. Radius the seams too - you don't really want a crisp sharp edge.
It's best to mask off the sides or any place the resin might dribble and drip. It will always dribble and drip when you aren't looking. Don't expect to outsmart it.
Next cut your tapes to length. Brush the seam with epoxy and slap the tape down and saturate the tape with more epoxy brushed in. Like this:
Usually I advise more than one layer of glass on the outer seams to allow for some abrasion. Often I will put a layer of glass cloth over the bottom panel for the same reason. I have never glassed the total exterior or interior of any of my boats. The second layer goes right over the first before the first cures. Saturate well. Look for dry spots that will appear white whereas saturated glass appears clear. The edge of the second layer should be staggered a bit from the first layer like this to prevent a big ridge on the edge.
After cure, sand lightly but not through the glass. I do feather out the glass edges with a rubber disk sander in a drill with pretty coarse paper. Then I give the tapes a light layer or two of filler to fill any weave followed by another light sanding. Then I try to accept any remaining imperfections and paint the hull. You can wear yourself out being a perfectionist about this and you are welcome to do so. If your boat gets hard use you won't notice those imperfections at all after once or twice to the lake.
And remember those places where the temporary forms stopped the interior tapes. Once the forms come out, sand and rough up the ending points, fillet and tape those final gaps.
...We'll dig deeper into panel stiffness.
ROGUE, ROWBOAT, 10' X 3.5', 60 POUNDS EMPTY
I keep trying my hand at these little rowing boats. The idea is that they will cartop very easily, row quite well with one person and take two adults in a pinch. I also try to keep them somewhat seaworthy and easy to beach.
Rogue should be a very good cartop all around rowing boat. I kept her length down to just 10' which should mean that the boat will be short enough to cartop without bumper ties. That gets important because automobiles lost their metal bumpers back in 1990. It will also keep the weight to about 60 pounds for an easy lift to the roof. It should be easier to load than an 8 foot dink because those really short boats often can't be loaded one end at a time - they must be put up there all at once. Even ten footer might be too short for "one end at a time" loading although I know I can load an 11' Piccup Pram that way on a compact car, at least.
I kept the capacity up there at about 400 pounds with lines such that the stem and stern are still out of the water. With a light weight hull that should mean the boat might still row well with two adults. One might ask why longer boats are preferred. First, a longer boat can be faster at any loading because when operated at a low power mode, the speed of the boat is limited by waterline length, the longer the faster. That's because long boats make less waves that short boats and those waves are made by your arms in a rowboat. There are limits to the length, of course, but a really serious racing hull might be 20' long or more for a single seater. (I once saw on a college campus a racing boat for a four man crew, over 60' long as I recall. The rowing coach was trying to recruit men to row it, saying he preferred red shirted basketball players - the bigger and taller the better.) And one might remember that there are other elements that cause drag such as skin friction and windage, both factors get worse as boat length increases.
I went to multichines with Rogue and would expect her to be a good sea boat for the size, at least when rowed solo. (That is another argument for a longer boat. When loaded with a passenger the weight in the boat gets pushed to the ends and in rough water the boat will not lift itself over the waves but instead pushes through them and that usually slows you down. A longer boat is not affected as badly here.) I'm quite certain that a multichine hull has less drag all around than a flat bottomed boat, although I suspect the V is better yet. The multichine hull is a very good compromise in that it will beach flat and have draft somewhere between a flattie and a V bottom, everything else being equal. My first rowboat, Roar, had a hull like Rogue, but was 14' long. I found out from it that a multichine has little resistance to side loads, as in a cross wind. Thus to avoid needing to row in a "crab" in crosswinds, a multichine needs a lot of skeg area and a full length keelson.
Steven Fisher in built the prototype in New York very quickly, faster than could be reported on in this twice-a-month webpage. He writes:
A successful launch. My daughter and son-in-law just bought a farm and this will be perfect for the 2 acre pond. As you can see I put in the Bolger seat. So far it seems to work well enabling me to easily change rowing positions to maintain balance etc. You can't see it in the photos but I inadvertently installed the keelson vertically so it's 3/4" deeper than spec but doesn't seem to make a difference. I've scratched the idea of a motor but would like to try a sail. Suggestions as to mast placement, leeboard etc would be appreciated. I have aluminum for a mast and bamboo for spars. In all of the above I forgot to mention that it's very east to row and I found that 6' oars work a bit better for me than the 7s. A quick and easy build of a fun boat.
Good job, Steve! But when you get to bigger waters be sure to row facing backwards, you can get a lot more power into it than with push rowing. With push rowing you can see what you are about to hit sooner, important on a two acre pond. I talked Steve out of fitting a motor which will never work well with a fine lined stern. Looks like I haven't talked him out of the sail rig yet. With no built in flotation Rogue, like any open traditional boat, will totally swamp in a capsize and you will need to be rescued, you won't be able to rescue yourself. LF Herreschoff in one of his books talks about this - with an open wooden boat that has been swamped you must bail it out before getting back inside by swimming beside as you bail. Then get in over the stern if you can. LF used the word "heartbreaking" as I recall since it was very iffy for anyone to try. If you want to sail, better to try Mixer or Piccup which are only slightly larger but have large buoyancy boxes that will permit self rescue.
Construction is taped seam. Three sheets of 1/4" plywood will do it and only two thirds of that ends up in the boat, the rest used as temporary forms that are removed. No jigs or lofting.
Plans for Rogue arel $20.
Some of you may know that in addition to the one buck catalog which now contains 20 "done" boats, I offer another catalog of 20 unbuilt prototypes. The buck catalog has on its last page a list and brief description of the boats currently in the Catalog of Prototypes. That catalog also contains some articles that I wrote for Messing About In Boats and Boatbuilder magazines. The Catalog of Prototypes costs $3. The both together amount to 50 pages for $4, an offer you may have seen in Woodenboat ads. Payment must be in US funds. The banks here won't accept anything else. (I've got a little stash of foreign currency that I can admire but not spend.) I'm way too small for credit cards.
I think David Hahn's Out West Picara is the winner of the Picara race. Shown here on its first sail except there was no wind. Hopefully more later. (Not sure if a polytarp sail is suitable for a boat this heavy.
Here is a Musicbox2 I heard about through the grapevine.
HOLY COW! A Jukebox2 takes shape in Minnesota. Unheated shop means no work during the winter. Check out that building rig! (Wait a minute! I just got a CD of photos of a Jukebox2 finished in the Sydney, Australia area by Ted Arkey!)
And the Vole in New York is Garth Batista's of www.breakawaybooks.com, printer of my book and Max's book and many other fine sports books. Boat is done, shown here off Cape Cod with mothership Cormorant in background, Garth's girls are one year older. Beautiful job!
AN INDEX OF PAST ISSUES
BACK ISSUES LISTED BY DATE
Mother of All Boat Links
The Boatbuilding Community
Kilburn's Power Skiff
Bruce Builds Roar
Rich builds AF2
JB Builds AF4
JB Builds Sportdory
Hullforms Download (archived copy)
Plyboats Demo Download (archived copy)
Brokeboats (archived copy)
Brian builds Roar2 (archived copy)
Herb builds AF3 (archived copy)
Herb builds RB42 (archived copy)
Barry Builds Toto
Table of Contents