Jim Michalak's Boat Designs

118 E Randall, Lebanon, IL 62254


A page of boat designs and essays.

(15Jan09)This issue will finish the knockdown essay. The 1 February issue will discuss buoyancy chambers and swamping.

THE BOOK IS OUT!

BOATBUILDING FOR BEGINNERS (AND BEYOND)

is out now, written by me and edited by Garth Battista of Breakaway Books. You might find it at your bookstore. If not check it out at the....

ON LINE CATALOG OF MY PLANS...

...which can now be found at Duckworks Magazine. You order with a shopping cart set up and pay with credit cards or by Paypal. Then Duckworks sends me an email about the order and then I send the plans right from me to you.

Left:

Family fun on Gordo Barcom's Laguna.

 


Contents:

 

Contact info:

jim@jimsboats.com

Jim Michalak
118 E Randall,
Lebanon, IL 62254

Send $1 for info on 20 boats.

 

 

Contents


Knockdown Recovery 2

RECAP....

In the last issue I presented an essay about knockdown recovery demonstrated by Herb McLeod with his AF3. This year Max Wawrzyniak completed an AF3 in St. Louis not far from here. One weekend we went out for a boat camp at Calylye Lake. On that Saturday there was no significant wind and we decided to take advantage of the calm conditions by doing a practice capsize of his AF3 (shown below with a classic 2hp Neptune mounted).

On reason I was looking forward to the test was to scope out the situation which Norm Wolf ran into with his Normsboat where the capsized boat floated nicely on its side and was easy to right but had its centerline slot pretty close to the water. Here is a photo of the situation.

Few knockdowns happen in calm conditions of course, and that open slot might look inviting to a large wave. When I made the first boat like this about ten years ago, a Bolger Jinni modified to have a small slot top cabin, I was careful to add segmented hard covers over the slot when sailing in rough conditions. I never capsized that boat and can't say how it would have done. But I feel the slot was covered sufficiently to minimize the effect of waves. I did similar designs like Pencilbox and AF2 and showed the plywood slot covers on the drawings but none of the builders built them. I'll admit that hardcovers are a pain. Eventually everyone moves towards soft covers and that is what Norm and Max use. I'm not sure how effective a fabric slot cover would be in keeping the waves out but I'm pretty sure it would be a lot better than nothing. Remember that the cover is not supposed to keep the water out for hours but just for a few minutes while the skipper swims around and rights the boat.

For any slot cover, the mast is something of a problem in that it is mounted on the side of the slot and would need to protrude through the cover if the cover were used while sailing. It was fairly easy to make a slot it my plywood slot covers. I think someone handy with a sewing machine could do the same with a soft cover but that is only speculation.

THE CAPSIZE...

Here is what we did. The AF3 was beached and we removed the motor and all the loose things, although Max is much better at secure stowage than most of us. The boat was walked into waist deep water, parallel to the shore, and anchors run out from the bow and stern. The halyard was secured to the mast and its free end given to me close to the shore. So I could pull the boat over with the halyard while the anchors held the boat in place.

The sail was stowed to keep tangles to a minimum but the sail and boom can have an effect on the result. I would expect the boat would be slightly less stable due to the weight of the sail and boom up high. Once the boat is knocked down the boom and sail can help float the boat and keep the boat from going turtle. In fact that effect is really strong with a lug sail who's yard acts like a float out on the top of the mast. Then when it comes time to right the boat it is very very important to totally release the sheet because if water pools in the sail as you try to raise it off the water the weight of that water can make the boat much harder to right. (There can be other effects. Remember wind surfers? You never see them any more but 15 years ago they were all the rage. One day I was out sailing when a young woman fell off a windsurfer nearby. She climbed back on and raised the sail with the rope. "Did you see that!" she exclaimed. "What?" says I. "There were five fish in that sail when I pulled it up!" says she.} And don't forget that if you raise the boat upright with the sheet tight that boat might sail off without you!

Max sat in his boat in his usual sailing position while I tugged it over. He has a tilt angle indicator on his bulkhead although it maxes out at 40 degrees, I think.

I pulled it over and thought in a subjective way that the maximum righting force came at about 20 degrees which is what I expected. Almost any unballasted sharpie seems to behave like that. I continued to pull until the cockpit coaming was about to go under and flood the cockpit. Max said that was at about the limit of his gauge, 40 degrees. I was surprised that the boat still had substantial righting ability at that point unlike my old Jinni which capsized twice in tis career, both times it seems like way before any water came over the rail. But the AF3 was still hanging in there and you might be able to recover right up until then. Max had covers over his oarports which leaked slightly - a good indication that it is time to release the sheet although I can't imagine anyone seriously sailing one of these over 20 degrees of heel in a regular way.

Next I released the tension on the halyard so the boat rolled back upright. Warning! If you ever do a test like this give the skipper lots of warning because the boat rolls upright very quickly and the ride inside the boat can be rather violent!

Max checked things over and all was OK for the test to a full capsize. I tugged on the halyard and at about 45 degrees of heel the tension on the halyard was about zero. Over it came and I grabbed the mast when it approached horizontal and Max jumped out of the flooding cockpit. The righting moment continued in a negative way indicating the boat might turtle but when the mast tip hit the water it settled on its side like this:

Max righted the boat in an instant. He said there was nothing to it. Norm said there was nothing righting Normsboat and Herb said there was nothing to righting his AF3.

Once righted Max climbed back into the boat using the step hole he had cut into his rudder. It worked very well and I am going to show such a step hole in all future boats. The hole has no noticable effect on sailing.

Max bailed it out and that takes a while. There was no water in the cabin or stern locker but it was maybe 6" deep in the cockpit. In a real capsize this would be a critical time since the water in the flooded cockpit would roll around with each wave and make the boat a lot less stable. It is important to have a good bailing bucket handy and secured to the boat if you are sailing in capsize conditions.

When it was all squared away we capsized it again so I could get an idea of the effort needed to right it. Not much required. With Jinni it took my weight on the leeboard to right the boat but with AF3 I never got that far. When I waded around the stern I grabbed the chine and pushed on the bottom and up she came.

WHAT I THINK IT ALL MEANS....

I'm going to draw a narrower slot in future designs and go back to showing the plywood slot covers.

One question I have to ask myself is if a bit of added ballast will make these designs self righting. Not with the crew inside because that can be a very difficult situation to scope out in every way, but with the empty boat righting itself after the capsize and the crew is swimming. Then the boat self rights by itself before waves have a chance to flood into the slot. The crew doesn't need to swim except to get to the rudder toe slots and back into the boat. Then it is bail time. From what I have seen the amount of ballast needed might not be much, maybe less that 50 pounds. Maybe less if the weight is mounted on the tip of the leeboard. But you can't always plan on the leeboard being down and the tip ballast might make the board very hard to pull up. You can of course see a great danger in such a boat in that it might sail off without you very quickly so on second thought it isn't such a good idea. Then again, that situation is no different from the present where you must have the sheet loose and have a good grip on the boat when it pops upright.

But it would not be a major effort to find out. I might check it out using the Hullforms program but even better would be to wait until the warm water returns and Max gets bored with sailing on a calm day. Then we haul it over again and see how much weight is needed to make it right by itself. Luckily Max is a good sport.

UPDATE 2007...

...I heard of three capsizes with swampings this year, two in AF3 and one in a Frolic2. What they all had in common was someone standing in the open slot top at the time. Clearly that won't work - the weight has to be in the cockpit and the slot well covered and secured.

LADYBUG CAPSIZE UPDATE:

Chuck Leinweber of duckworksmagazine.com did a practice capsize at his Texas messabout this past year, took photos, and wrote up the experience:

"I wanted to add some notes to the pictures of the Ladybug capsize test:

It's hard to tell, but the bottom drops off quickly here and the boat never touched. Sometimes it looks like it might be sitting on the bottom, but it was happily bobbing in the waves even when completely on it's side. It took a surprising bit of effort to pull the boat over even though it was entirely stripped of gear.

Once on it's side, the boat floated on the yardarm with the hull high in the water. That is the tiller in the air since the rudder flopped to starboard.

Now I start to try to bring it back up. I probably should have done it the other way so that I could have pulled the leeboard, but I guess in a real knock-down, you don't get to choose.

Now I'm grabbing the gunwale and am putting some weight on it. - that did not work, so I climbed on the mast - at this point the yardarm went under and may have hit the bottom. Anyway, I swung myself over the side.....

...and hanging onto the gunnel, easily tipped the boat back upright.

I tried to simulate getting back in the boat in deep water by bending my knees and pulling myself in with my arms only. This was surprisingly easy.

There was a bit of water in the cockpit, but that was easily bailed. I think the boat would have sailed that way unless it was very brisk.

Skip Johnson helped me bail the boat out. The hatches were built a little oversized to accommodate an ice chest (yes, we are spoiled) but only leaked a few tablespoons of water into the flotation chambers. Now we pack our gear in dry bags when we go cruising."

MORE PONDERING...

If you are going to sail in capsize conditions you really need to:

...Practice a capsize until you can right the boat and get going again. Practice usually happens in mild conditions and in real capsize conditions things will be worse. Then again the fear factor in a real capsize will help your strength and quickness.

...Make sure all your gear is well secured. If not you will lose it. In this catagory would be important boat parts like your rudder and mast, both of which may leave your boat if not well secured in position if the boat is sideways or inverted.

...Keep bailing equipment handy and secured to the boat. I think that a couple of scoops made from gallon jugs might be best, one tied to each side of the hull so you won't have to reach across a flooded boat to get a scoop. Should be large enough to bail a good amount of water with one hand because you will need the other hand to hold on to the boat. Should not be so small that it will take a long time to bail.

...Give a lot of thought to righting and reboarding the boat. I would suggest having lines that allow you to pull down on the wale from the bottom even if you can't reach the wale or stand on a leeboard. Also seriously consider the slot in the rudder to give a toe hold to reboard. Most smaller boats if swamped will be too unstable to reboard over the side - the water in the boat will slosh towards you as you try to hoist yourself over the wale, recapsizing the boat.

Contents


Caroline

CAROLINE, SAILBOAT, 18' X 6', 750 POUNDS EMPTY

Caroline started as a blend of Philsboat and Frolic2. The idea was for a little more cabin room than Philsboat and hopefully with the same seakeeping ability that Frolic2 has demonstrated. I made it a little deeper and wider and with a longer cabin than Philsboat. It all added up to about 30% more cabin volume. But it is also more boat to build and pay for and haul so the other boats, which are lighter and cheaper, still havenít been made obsolete as far as I am concerned.

One interesting side to this sort of house design is that if you add a motor well, as this one has, the stern gets pretty busy since the only way you can run a normal tiller to the rudder is under the aft deck. To get a good swing of the rudder that aft deck needs to be short and wide if that motor is to live there too. I think I have it all crammed in there such that it might work but even so the rudder is well offset to one side, as it was successfully done with Philsboat.

The builder wanted a yawl rig (she wants to coastal cruise the Maine coast) but I added the mizzen as I do now, keeping the basic balance such that you could sail it without the mizzen.

I'm still carrying Caroline as a prototype even though she was completed and cruised in the summer of 2008. Problem was that the mizzen wasn't ready in time for the cruise so they went to sea without. She sailed fine but I underestimated the anchor situation in Maine where the tides won't let you beach a heavy boat. Any boat like this will swing at anchor in a wind and so did Caroline. The mizzen is supposed to stop that so hopefully we shall see in the 2009 cruise if she works AOK with the mizzen. But here are some photos of the first launch/cruise:

You can see that these Birdwatcher cabins are simple and roomy.

Looks like six sheets of 1/4", ten sheets of 3/8" and three sheets of 1/2"". Taped seam construction.

Plans for Caroline are $35 until one is built and tested.

Contents


Prototype News

Some of you may know that in addition to the one buck catalog which now contains 20 "done" boats, I offer another catalog of 20 unbuilt prototypes. The buck catalog has on its last page a list and brief description of the boats currently in the Catalog of Prototypes. That catalog also contains some articles that I wrote for Messing About In Boats and Boatbuilder magazines. The Catalog of Prototypes costs $3. The both together amount to 50 pages for $4, an offer you may have seen in Woodenboat ads. Payment must be in US funds. The banks here won't accept anything else. (I've got a little stash of foreign currency that I can admire but not spend.) I'm way too small for credit cards.

I think David Hahn's Out West Picara is the winner of the Picara race. Shown here on its first sail except there was no wind. Hopefully more later. (Not sure if a polytarp sail is suitable for a boat this heavy.

Here is a Musicbox2 I heard about through the grapevine.

This is Ted Arkey's Jukebox2 down in Sydney. Shown with the "ketchooner" rig, featuring his own polytarp sails, that is shown on the plans. Should have a sailing report soon.

And the Vole in New York is Garth Batista's of www.breakawaybooks.com, printer of my book and Max's book and many other fine sports books. Boat is done, shown here off Cape Cod with mothership Cormorant in background, Garth's girls are one year older. Beautiful job! I think Garth is using a small lug rig for sail, not the sharpie sprit sail shown on the plans, so I will continue to carry the design as a prototype boat.

And a new Down Under Blobster is off cruising under outboard power as it waits for its sailrig.

A view of the Caroline prototype showing a lot of the inside, crew on fore deck. Beautiful color:

And here is another making I think its maider voyage in the Texas 200. (I'm told the Chinese rig will be replaced by the blueprint rig.)

I gotta tell you that on the Caroline bilge panels I made an error in layout and they are about 1" too narrow in places on the prototype plans. I have them corrected but it always pays, even with a proven design, to cut those oversized and check for fit before final cutting.

And a Deansbox seen in Texas:

And in Texas Gordo Barcom has completed the first Laguna and I hope to give a full report soon. Here he blasts along on his first flight:

A Twister goes together in good shape:

Contents


AN INDEX OF PAST ISSUES

THE WAY BACK ISSUE ARCHIVES

1feb09, Aspect Ratio 2, Mayfly16

15feb09, IMB Capsize, IMB

1mar09, Mizzens, Blobster

15mar09, Lugsail Rigging, Imresboat

1apr09, Laguna, Frolic2

15apr09, Rigging Sharpie Sprits, Sportdory

1may09, Small Boat Rudders, Robbsboat

15may09, Rowing Gear, Roar2

1jun09, A Bimini Boot, Ozarkian

15jun09, Phil Bolger, Vector

1jul09, Rend Lake 2009, Fatcat2

15jul09, Rowboat Setup, Mikesboat

1aug09, Sail Area Math, Family Skiff

15aug09, Beach Designs, Cormorant

1sep09, Taped Seams, Trilars

15sep09, Birdwatcher Cabins, Philsboat

1oct09, Bevels, Larsboat

15oct09, Transom Height, Jonsboat

1nov09, Ballast Again, Piccup Pram

15nov09, Ballast Again2, Caprice

1dec09, Weight Problems, AF4Casa

15dec09, Ballast Again3, Raider

1jan10, Knockdown Recovery 1, RioGrande

SOME LINKS

Mother of All Boat Links

Cheap Pages

Duckworks Magazine

The Boatbuilding Community

Kilburn's Power Skiff

Bruce Builds Roar

Dave Carnell

Rich builds AF2

JB Builds AF4

JB Builds Sportdory

Hullform Download

Plyboats Demo Download

Brokeboats

Brian builds Roar2

Herb builds AF3

Herb builds RB42

Barry Builds Toto



Table of Contents